5i' (cs,2) Disk. 360 NF01/027 (OPM = NF01) (cs,3) Disk. 361 NF01/034 (OPM = NF02) (ATTENTION NOTE REPETITIVE COMMENCANT AU NUMERO 15): xx xx xxxx xx xx xxxx xx xx xxxx xx xx xxxx xx xx xxxx xx xx xxxx xx xx xxxx xx xx xxxx xx xx xxxx xx xx xxxx xx xx xxxx xx xx xxxx xx xx xxxx xx xx xxxx (1BT) (BT10) Disk. 360 NF01/005 (67.TE.05.E) (A1.23e) / [26e] FOLIOS: 175 - 227 (DO PRC.COSY.2) MEP [PA1] : OK= [1] Saisie 25.04.89 SB ID + LASER 22.05.89 CW MAJ diskette 24.05.89 CW Corr. LASER (1re epreuve) = 3eme 26.05.89 GG Espaces reserves 30.05.89 CW _________________________ National option. National option. National option. National option. National option. National option. National option. National option. National option. National option. National option. National option. National option. National option. AJOUTER (PA1) (CL1,0,0,0) pour MEP MEP + LASER 13.06.89 GH/PC Corr. MEP Insertion des tableaux (tabulateurs...) BAT du 6/6/89 07.07.89 PV MAJ s/disquettes 2.07.89 CD MONTAGE: FIN DU S 12.7 EN-TETE DE CETTE PAGE 13 Signalling route management 13.1 General National option. The purpose of the signalling route management function is to ensure a reliable exchange of information between the signalling points about the availability of the signalling routes. The unavailability, restriction and availability of a signal- ling route is communicated by means of the transfer-prohibited, transfer-restricted and transfer allowed procedures, respectively in SS 13.2, 13.4 and 13.3. Recovery of signalling route status information is made by means of the signalling-route-set-test procedure specified in S 13.5. In the international signalling network, congestion of a route set is communicated by means of the transfer-controlled (TFC) mes- sages specified in S 13.6. In national networks, congestion of a signalling route set may be communicated by means of the TFC as specified in SS 13.7 and 13.8 and the signalling route set congestion test procedure specified in S 13.9. 13.2 Transfer prohibited 13.2.1 The transfer-prohibited procedure is performed at a signalling point acting as a signalling transfer point for messages relating to a given destination, when it has to notify one or more adjacent signalling points that they must no longer route the con- cerned messages via that signalling transfer point. The transfer-prohibited procedure makes use of the transfer-prohibited message which contains: - the label, indicating the destination and ori- ginating points; - the transfer-prohibited signal; and - the destination for which traffic transfer is no longer possible. Format and code of these messages appear in S 15. Transfer prohibited messages are always addressed to an adja- cent signalling point. They may use any available signalling route that leads to that signalling point. 13.2.2 A transfer-prohibited message relating to a given destination X is sent from a signalling transfer point Y in the following cases: i) When signalling transfer point Y starts to route (at changeover, changeback, forced or controlled rerouting) signal- ling destined to signalling point X via a signalling transfer point Z not currently used by signalling transfer point Y for this traffic. In this case the transfer-prohibited message is sent to signalling transfer point Z. ii) When signalling transfer point Y recognizes that it is unable to transfer signalling traffic destined to sig- nalling point X (see SS 5.3.3 and 7.2.3). In this case a transfer-prohibited message is sent to all accessible adjacent sig- nalling points (Broadcast method). iii) When a message destined to signalling point X is received at signalling transfer point Y and Y is unable to transfer the message. In this case the transfer prohibited message is sent to the adjacent signalling point from which the message concerned was received (Response Method). iv) When an adjacent signalling point Z becomes accessible, STP Y sends to Z a transfer prohibited message concern- ing destination X, if X is inaccessible from Y (see S 9). v) When a signalling transfer point Y restarts, it _________________________ The possibility of referring to a more general destina- tion than a single signalling point (e.g. a signalling region), or more restrictive destination than a signal- ling point is for further study. broadcasts to all accessible adjacent signalling points transfer prohibited messages concerning destination X, if X is inaccessible from Y (see S 9). As long as transfer-prohibited messages for a destination are being transmitted according to criteria i), ii), iv), or v) above, and also within T8 (see S 16) after the last transfer-prohibited message was transmitted, no transfer-prohibited messages will be sent via the Response Method (criterion iii) above) referring to that destination. Examples of the above situation appear in Recommendation Q.705. 13.2.3 When a signalling point receives a transfer-prohibited message from signalling transfer point Y it performs the actions specified in S 7 (since reception of transfer-prohibited message indicates the unavailability of the concerned signalling route, see S 3.4.1). In other words, it may perform forced re-routing and, if appropriate, generate additional transfer-prohibited messages. 13.2.4 In some circumstances it may happen that a signalling point receives either a repeated transfer-prohibited message relat- ing to a nonexistent route (i.e. there is no route from that sig- nalling point to the concerned destination via signalling transfer point Y, according to the signalling network configuration) or to a destination which is already inaccessible, due to previous failures; in this case no actions are taken. 13.3 Transfer allowed 13.3.1 The transfer-allowed procedure is performed at a sig- nalling point, acting as signalling transfer point for messages relating to a given destination, when it has to notify one or more adjacent signalling points that they may start to route to it, if appropriate, the concerned messages. The transfer-allowed procedure makes use of the transfer-allowed message which contains: - the label, indicating the destination and ori- ginating points; - the transfer-allowed signal; and - the destination for which transfer is now possi- ble. The format and code of these messages appear in S 15. Transfer allowed messages are always addressed to an adjacent signalling point. They may use any available signalling route that leads to that signalling point. 13.3.2 A transfer-allowed message relating to a given destination "X" is sent from signalling transfer point "Y" in the following cases: i) When signalling transfer point "Y" stops routing (at changeback or controlled rerouting) signalling traffic destined to signalling point "X" via a signalling transfer point "Z" (to which the concerned traffic was previously diverted as a conse- quence of changeover or forced rerouting). In this case the transfer-allowed message is sent to signalling transfer point "Z". ii) When signalling transfer point "Y" recognizes that it is again able to transfer signalling traffic destined to signalling point "X" (see SS 6.2.3 and 8.2.3). In this case a transfer-allowed message is sent to all accessible adjacent signal- ling points. (Broadcast method). Examples of the above situations appear in Recommendation Q.705. 13.3.3 When a signalling point receives a transfer-allowed message from signalling transfer point "Y", it performs the actions specified in S 8 (since reception of a transfer-allowed message indicates the availability of the concerned signalling route, (see S 3.4.2)). In other words, it may perform controlled re-routing and, if appropriate, generate additional transfer-allowed messages. 13.3.4 In some circumstances it may happen that a signalling point receives either a repeated transfer-allowed message or a transfer-allowed message relating to a non-existent signalling route (i.e. there is no route from that signalling point to the concerned destination via signalling transfer point Y according to the signalling network configuration); in this case no actions are taken. 13.4 Transfer-restricted (National option) 13.4.1 The transfer restricted procedure is performed at a signalling point acting as a signalling transfer point for messages relating to a given destination, when it has to notify one or more adjacent signalling points that they should, if possible, no longer route the concerned messages via the signalling transfer point. The transfer-restricted procedure makes use of the _________________________ The possibility of referring to a more general destina- tion than a single signalling point (e.g. a signalling region), or a more restrictive destination than a sin- gle signalling point is for further study. transfer-restricted message which contains: - the label, indicating the destination and ori- ginating points; - the transfer-restricted signal, and - the destination for which traffic is no longer desirable. Formats and codes of this message appear in S 15. Transfer restricted messages are always adressed to an adja- cent signalling point. They may use any available signalling route that leads to that signalling point. Note - Undesirable situations result in increased signalling delays, possibly overloading portions of the network. These ineffi- ciencies could be avoided if the traffic can be appropriately diverted. 13.4.2 A transfer-restricted message relating to a given des- tination "X" is sent from a signalling transfer point "Y" when the normal link set (combined link set) used by signalling point "Y" to route to destination "X" experiences a long-term failure such as an equipment failure, or there is congestion on an alternate link set currently being used to destination "X". In this case, a transfer-restricted message is sent to all accessible adjacent sig- nalling points. When an adjacent signalling point "X" becomes accessible, the STP "Y" sends to "X" transfer-restricted messages concerning desti- nations that are restricted from "Y" (see S 9). When a signalling point Y restarts, it broadcasts to all accessible adjacent signalling points transfer restricted messages concerning destinations restricted from "Y" (see S 9). Note - Characterization of long term failure remains for further study. 13.4.3 When a signalling point receives a transfer-restricted message from signalling transfer point "Y" and has an alternative equal priority link set available and not restricted to destination "X", it performs the actions in S 8.2. In other words, it performs controlled rerouting to maintain the sequence of mes- sages while diverting them to the alternative link set. If it can- not perform alternate routing to destination "X" because no alter- native link set is available, it may generate additional transfer-restricted messages. 13.4.4 In some circumstances, it may happen that a signalling point receives either a repeated transfer-restricted message or a transfer-restricted message relating to a non-existent route (i.e. there is no route from that signalling point to the concerned destination via signalling transfer point "Y", according to the signalling network configuration); in this case, no actions are taken. 13.4.5 When a transfer-restricted message is received updating a transfer-prohibited status, signalling traffic management decides if an alternative route is available or restricted; if it is not (i.e. no alternative route exists), the concerned traffic is res- tarted towards the signalling point from which the transfer-restricted message was received. Otherwise, no other actions are taken. 13.5 Signalling-route-set-test 13.5.1 The signalling-route-set-test procedure is used at a signalling point to test whether or not signalling traffic towards a certain destination may be routed via an adjacent signalling transfer point. The procedure makes use of the signalling-route-set-test mes- sage, and the transfer-allowed and the transfer-prohibited pro- cedures. The signalling-route-set-test message contains: - the label, indicating the destination and ori- ginating points; - the signalling-route-set-test signal; - the destination, the accessibility of which is to be tested; and - the current route status of the destination being tested. Format and coding of this message appear in S 15. 13.5.2 A signalling-route-set-test message is sent from a sig- nalling point after a transfer-prohibited or transfer-restricted message is received from an adjacent signalling transfer point. In this case, a signalling-route-set-test message is sent to that sig- nalling transfer point referring to the destination declared inac- cessible or restricted by the transfer-prohibited or transfer-restricted message, every T10 period (see S 16) until a transfer-allowed message, indicating that the destination has become accessible, is received. _________________________ The possibility of referring to a more general destina- tion than a single signalling point (e.g. a signalling region), or a more restrictive destination than a sin- gle signalling point is for further study. This procedure is used in order to recover the signalling route availability information that may not have been received because of some signalling network failure. 13.5.3 A signalling-route-set-test message is sent to the adjacent signalling transfer point as an ordinary signalling net- work management message. 13.5.4 At the reception of a signalling-route-set-test mes- sage, a signalling transfer point will compare the status of the destination in the received message with the actual status of the destination. If they are the same, no further action is taken. If they are different, one of the following messages is sent in response, dictated by the actual status of the destination: - a transfer-allowed message, referring to the destination the accessibility of which is tested, if the signalling transfer point can reach the indicated destination via a signalling link not connected to the signalling point from which the signalling-route-set-test message was originated, and via the nor- mal routing; - a transfer-restricted message when access to the destination is possible via an alternative to the normal routing which is less efficient, but still not via the signalling point from which the signalling route-set-test was originated; - a transfer-prohibited message in all other cases (including the inaccessibility of that destination). 13.5.5 At the reception of the transfer-prohibited or transfer-allowed message, the signalling point will perform the procedures specified in SS 13.2.3 or 13.2.4 and 13.3.3 or 13.3.4 respectively. 13.6 Transfer controlled (International network) The only use made of the transfer controlled procedure in the international signalling network is to convey the congestion indi- cation from the SP where congestion was detected to the originating SP (see S 11.2.3) in a transfer-controlled message. The transfer-controlled message contains: - the label, indicating the destination and ori- ginating points; - the transfer controlled signal; - the identity of the congested destination. The format and coding of the transfer controlled message appear in S 15. 13.7 Transfer controlled (National option with congestion priorities) 13.7.1 The transfer-controlled procedure is performed at a signalling transfer point for messages relating to a given destina- tion, when it has to notify one or more originating signalling points that they should no longer send to the concerned destination messages with a given priority or lower. The transfer-controlled procedure makes use of the transfer-controlled message which contains: - the label, indicating the destination and ori- ginating points, - the transfer-controlled signal, - the destination for which messages with a congestion priority lower than the specified congestion status should no longer be sent, and - the current congestion status encountered in routing a particular message towards the concerned destination. The format and coding of this message appear in S 15. 13.7.2 A transfer-controlled message relating to a given des- tination "X" is sent from a signalling transfer point "Y" in response to a received message originating from signalling point "Z" destined to signalling point "X" when the congestion priority of the concerned message is less than the current conges- tion status of the signalling link selected to transmit the con- cerned message from "Y" to "X". In this case, the transfer-controlled message is sent to the originating point "Z" with the congestion status field set to the current congestion status of the signalling link. 13.7.3 When the originating signalling points "Z" receive a transfer-controlled message relating to destination "X", if the current congestion status of the signalling route set towards destination "X" is less than the congestion status in the transfer-controlled message, it updates the congestion status of the signalling route set towards destination "X" with the value of the congestion status carried in the transfer-controlled message. 13.7.4 If within T15 (see S 16) after the receipt of the last transfer-controlled message relating to destination "X", signalling point "Z" receives another transfer-controlled message relating to the same destination, the following action is taken: If the value of the congestion status carried in the new transfer-controlled message is greater than the current value of the congestion status of the signalling route set towards destination "X", then the current value is updated by the new value. 13.7.5 If T15 (see S 16) expires after the last update of the signalling route set towards destination "X" by a transfer-controlled message relating to the same destination, the signalling-route-set-congestion-test procedure is invoked (see S 13.9). 13.7.6 In some circumstances it may happen that a signalling point receives a transfer-controlled message relating to a destina- tion which is already inaccessible due to previous failures; in this case the transfer-controlled message is ignored. 13.8 Transfer controlled (National option without conges- tion priorities) The only use made of the TFC procedure by the national signal- ling network, using multiple congestion states without congestion priorities, is to convey the congestion indication primitive from the SP where congestion was detected to the originating SP (see S 11.2.5) in a transfer-controlled message. The transfer-controlled message contains: - the label, indicating the destination and ori- ginating points; - the transfer-controlled signal; - the identity of the congested destination; - the current congestion status encountered in routing a particular message towards the concerned destination. The format and coding of this message appear in S 15. 13.9 Signalling-route-set-congestion-test (National Option) 13.9.1 The signalling-route-set-congestion-test procedure is used at an originating signalling point to update the congestion status associated with a route set towards a certain destination. The purpose is to test whether or not signalling messages destined towards that destination with a given congestion priority or higher may be sent. In the case of a processor restart the congestion status of all signalling route sets will be initialized to the zero value. The response mechanism within the transfer-controlled procedure will correct signalling route sets whose congestion status does not have the zero value. The procedure makes use of the signalling-route-set-congestion-test message, and the transfer-controlled procedure. The signalling-route-set-congestion-test message contains: - the label, indicating the destination and ori- ginating points, and - the signalling-route-set-congestion-test signal. The format and coding of this message appear in S 15. 13.9.2 The signalling-route-set-congestion-test message differs from other signalling network management messages in that it is not assigned the highest congestion priority. Instead, the congestion priority assigned to a signalling-route-set-congestion-test message to be sent to a given destination is equal to one less than the current congestion status associated with the signalling route set towards the destination. 13.9.3 If within T16 (see S 16), after sending a signalling-route-set-congestion-test message, a transfer-controlled message relating to the concerned destination is received, the sig- nalling point updates the congestion status of the signalling route set towards the concerned destination with the value of the conges- tion status carried in the transfer-controlled message. Following this, the procedures specified in SS 13.9.4 and 13.9.5 are per- formed. If T16 (see S 16) expires after sending a signalling-route-set-congestion-test message without a transfer-controlled message relating to the concerned destination having been received, the signalling point changes the congestion status associated with the signalling route set towards the con- cerned destination to the next lower status. 13.9.4 Provided that the signalling route set towards destination "X" is not in the "unavailable" state, a signalling-route-set-congestion-test message is sent from an ori- ginating signalling point to destination "X" in the following cases: i) When T15 (see S 16) expires after the last update of the congestion status of the signalling route set toward destination "X" by a transfer-controlled message relating to the same destination. ii) When T16 (see S 16) expires after sending a signalling-route-set-congestion-test message to destination "X" without a transfer-controlled message relating to the same destina- tion having been received. After the congestion status has been decremented by one, the test is repeated, unless the congestion status is zero. 13.9.5 At the reception of a signalling-route-set-congestion-test message, a signalling transfer point will route it as an ordinary message, i.e. according to the procedure specified in S 2.3.5. 13.9.6 When a signalling-route-set-congestion-test message reaches its destination, it is discarded. 14 Common characteristics of message signal unit formats 14.1 General The basic signal unit format which is common to all message signal units is described in Recommendation Q.703, S 2. From the point of view of the Message Transfer Part level 3 functions, com- mon characteristics of the message signal units are the presence of: - the service information octet; - the label, contained in the signalling informa- tion field, and, in particular, the routing label. 14.2 Service information octet The service information octet of message signal units contains the service indicator and the sub-service field. The structure of the service information octet is shown in Figure 13/Q.704. Figure 13/Q.704, p. 14.2.1 Service indicator The service indicator is used by signalling handling functions to perform message distribution (see S 2.4) and, in some special applications, to perform message routing (see S 2.3). The service indicator codes for the international signalling network are allocated as follows: bits D C B A 0 0 0 0 Signalling network management messages 0 0 0 1 Signalling network testing and maintenance messages 0 0 1 0 Spare 0 0 1 1 SCCP 0 1 0 0 Telephone User Part 0 1 0 1 ISDN User Part 0 1 1 0 Data User Part (call and circuit related messages) 0 1 1 1 Data User Part (facility registration and cancellation messages) 1 0 0 0 Reserved for MTP Testing User Part 1 0 0 1 1 0 1 0 1 0 1 1 1 1 0 0 spare 1 1 0 1 1 1 1 0 1 1 1 1 .bp The allocation of the service indicator codes for national signalling networks is a national matter. However, it is suggested to allocate the same service indicator code to a User Part which performs similar functions as in the international network. 14.2.2 Sub-service field The sub-service field contains the network indicator (bits C and D) and two spare bits (bits A and B). The network | ndicator is used by signalling message handling functions (e.g., in order to determine the relevant version of a User Part), see SS 2.3 and 2.4. If the network indicator is set to 00 or 01, the two spare bits, coded 00, are available for possible future needs that may require a common solution for all international User Parts. If the network indicator is set to 10 or 11, the two spare bits are for national use. They may be used, for example, to indi- cate message priority, which is used in the optional flow control procedure in national applications. The network indicator provides for discrimination between international and national messages. It can also be used, for exam- ple, for the discrimination between functionally two national sig- nalling networks, each having different routing label structures and including up to 16 User Parts defined by the 16 possible codes of the service indicator. In the case of only one national signalling network the spare code of the network indicator reserved for national use can be used, for example, to define an additional 16 User Parts (making a total of 32 User Parts) for that national signalling network. The network indicator codes are allocated as follows: bits D C 0 0 International network 0 1 Spare (for international use only) 1 0 National network 1 1 Reserved for national use The international spare code (01) should not be used for implementing features which are to be provided both internationally and nationally. In national applications, when the discrimination provided by the network indicator between international and national messages is not used, i.e. in a closed national signalling network seen from the signalling point of view, the whole sub-service field can be used independently for different User Parts. 14.3 Label The structure and content of the label is defined for each User Part and is defined in the relevant specification. The common part of the label used for signalling message handling, the routing label, is specified in S 2.2. 15 Formats and codes of signalling network management messages 15.1 General 15.1.1 The signalling network management messages are carried on the signalling channel in message signal units, the format of which is described in S 14 and in Recommendation Q.703, S 2. In particular, as indicated in S 14.2 these messages are distinguished by the configuration 0000 of the service indicator (SI). The sub-service field (SSF) of the messages is used according to the rules indicated in S 14.2.2. 15.1.2 The signalling information field consists of an integral number of octets and contains the label, the heading code and one or more signals and indications. The structure and function of the label, and of the heading code, are described in SS 15.2 and 15.3 respectively; the detailed message formats are described in the following sections. For each message the sequence of fields is shown in the corresponding figure, including fields that may or may not be present. In the figures, the fields are shown starting from the right to the left (i.e. the first field to be transmitted is at the right). Within each field the information is transmitted least sig- nificant bit first. Spare bits are coded 0 unlesss otherwise indi- cated. 15.2 Label For signalling network management messages the label coincides with the routing label and indicates the destination and originat- ing signalling points of the message; moreover, in the case of mes- sages related to a particular signalling link, it also indicates the identity of the signalling link among those interconnecting the destination and originating points. The standard label structure of Message Transfer Part level 3 messages appears in Figure 14/Q.704; the total length is 32 bits. Figure 14/Q.704, p. The meaning and use of the destination point code (DPC) and of the originating point code (OPC) fields are described in S 2. The signalling link code (SLC) indicates the signalling link, connect- ing the destination and originating points, to which the message is related. If the message is not related to a signalling link, or another particular code is not specified, it is coded 0000. 15.3 Heading code (H0) The heading code (H0) is the 4 bit field following the label and identifies the message group. The different heading codes are allocated as follows: 0000 Spare 0001 Changeover and changeback messages 0010 Emergency changeover message 0011 Transfer controlled and signalling route set congestion messages 0100 Transfer-prohibited-allowed-restricted mes- sages 0101 Signalling-route-set-test messages 0110 Management inhibit messages 0111 Traffic restart allowed message 1000 Signalling-data-link-connection messages 1001 Spare 1010 User part flow control messages The remaining codings are spare. The synopsis of singalling network management messages is given in Table 1/Q.704. 15.4 Changeover message 15.4.1 The format of the changeover message is shown in Figure 15/Q.704. Figure 15/Q.704, p. 15.4.2 The changeover message is made up of the following fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.4.3 - Forward sequence number of last accepted message signal unit (7 bits) - A filler bit coded 0 15.4.3 The heading code H1 contains signal codes as follows: bit D C B A 0 0 0 1 Changeover order signal 0 0 1 0 Changeover ack- nowledgement signal 15.5 Changeback message 15.5.1 The format of the changeback message is shown in Figure 16/Q.704. Figure 16/Q.704, p. 15.5.2 The changeback message is made up of the following fields: - Label (32 bits) see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.5.3 - Changeback code (8 bits): see S 15.5.4 15.5.3 The header code H1 contains signal codes as follows: bit D C B A 0 1 0 1 Changeback declara- tion signal 0 1 1 0 Changeback ack- nowledgement signal 15.5.4 The changeback code is an 8 bit code assigned by the signalling point which sends the message according to the criteria described in S 6. 15.6 Emergency changeover message 15.6.1 The format of the emergency changeover message is shown in Figure 17/Q.704. Figure 17/Q.704, p. 15.6.2 The emergency changeover message is made up of the fol- lowing fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.6.3 15.6.3 The header code H1 contains signal codes as follows: bit D C B A 0 0 0 1 Emergency change- over order signal 0 0 1 0 Emergency change- over acknowledgement signal 15.7 Transfer-prohibited message 15.7.1 The format of the transfer-prohibited message is shown in Figure 18/Q.704. Figure 18/Q.704, p. 15.7.2 The transfer-prohibited message is made up of the fol- lowing fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.7.3 - Destination (14 bits): see S 15.7.4 - Spare bits (2 bits) code 00 15.7.3 The heading code H1 contains one signal code as fol- lows: bit D C B A 0 0 0 1 Transfer-prohibited signal 15.7.4 The destination field contains the identity of the sig- nalling point to which the message refers. 15.8 Transfer-allowed message 15.8.1 The format of the transfer-allowed message is shown in Figure 19/Q.704. Figure 19/Q.704, p. 15.8.2 The transfer-allowed message is made up of the follow- ing fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.8.3 - Destination (14 bits): see S 15.7.4 - Spare bits (2 bits) coded 00 Note - For the use of the 2 spare bits in the national option for a SIF compatibility mechanism, see Recommendation Q.701, S 7.2.6. 15.8.3 The heading code H1 contains one signal code as fol- lows: bit D C B A 0 1 0 1 Transfer-allowed signal 15.9 Transfer restricted message (national option) 15.9.1 The format of the transfer restricted message is shown in Figure 18/Q.704. 15.9.2 The transfer restricted message is made up of the fol- lowing fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.9.3 - Destination (14 bits): see S 15.9.4 - Spare (2 bits) coded 00 15.9.3 The heading code H1 contains one signal code as fol- lows: bit D C B A 0 0 1 1 Transfer restricted 15.9.4 The destination field contains the identity of the sig- nalling point to which the message refers. 15.10 Signalling-route-set-test message 15.10.1 The format of the signalling-route-set-test message is shown in Figure 20/Q.704. Figure 20/Q.704, p. 15.10.2 This message is made up of the following fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.10.3 - Destination (14 bits): see S 15.7.4 - Spare bits (2 bits) coded 00 15.10.3 The heading code H1 contains signal codes as follows: bit D C B A 0 0 0 1 Signalling-route-set-test signal for prohibited destina- tion 0 0 1 0 Signalling-route-set-test signal for restricted destination (national option) 15.11 Management inhibit message 15.11.1 The format of the management inhibit message is shown in Figure 20a/Q.704. Figure 20a/Q.704, p. 15.11.2 The management inhibit message is made up of the following fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.11.3 15.11.3 The header code H1 contains signal codes as follows: bit D C B A 0 0 0 1 Link inhibit signal 0 0 1 0 Link uninhibit sig- nal 0 0 1 1 Link inhibited ack- nowledgement signal 0 1 0 0 Link uninhibited acknowledgement signal 0 1 0 1 Link inhibit denied signal 0 1 1 0 Link force uninhi- bit signal 0 1 1 1 Link local inhibit test signal 1 0 0 0 Link remote inhibit test signal 15.12 Traffic restart allowed message 15.12.1 The format of the traffic restart allowed message is shown in Figure 21/Q.704. Figure 21/Q.704, p. 15.12.2 The traffic restart allowed message is made up of the fol- lowing fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.12.3 15.12.3 The heading code H1 contains one signal code as follows: bit D C B A 0 0 0 1 Traffic restart allowed signal 15.13 Signalling-data-link-connection-order message 15.13.1 The format of the signalling-data-link-connection-order message is shown in Figure 22/Q.704. Figure 22/Q.704, p. 15.13.2 The signalling-data-link-connection-order message is made up of the following fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.13.3 - Signalling data link identity (12 bits): see S 15.13.4 - Spare bits (4 bits) coded 0000. 15.13.3 The heading code H1 contains one signal code as follows: bit D C B A 0 0 0 1 Signalling-data-link-connection-order signal 15.13.4 The signalling data link identity field contains the cir- cuit identification code (CIC), or the bearer identification code (BIC) in case of a 64 kbit/s channel used to carry submultiplex data streams, of the transmission link corresponding to the signal- ling data link. 15.14 Signalling-data-link-connection-acknowledgement mes- sage 15.14.1 The format of the signalling-data-link-connection-acknowledgement message is shown in Figure 22a/Q.704. Figure 22a/Q.704, p. 15.14.2 The signalling-data-link-connection acknowledgement mes- sage is made up of the following fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.14.3 15.14.3 The heading code H1 contains signal codes as follows: bit D C B A 0 0 1 0 Connection-successful signal 0 0 1 1 Connection-not-successful signal 0 1 0 0 Connection-not-possible signal 15.15 Transfer controlled message 15.15.1 The format of the TFC message is shown in Figure 22b/Q.704. Figure 22b/Q.704, p. 15.15.2 The transfer controlled message is made up of the follow- ing fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.15.3 - Destination (14 bits): see S 15.15.4 - Spare (2 bits): see S15.15.5 15.15.3 The heading code H1 contains one signal code as follows: bit D C B A 0 0 1 0 Transfer controlled signal 15.15.4 The destination field carries the address of the destina- tion to which the message refers. 15.15.5 In national signalling networks using multiple congestion states, the spare bits in the transfer controlled message are used to carry the congestion status associated with the destination. 15.16 Signalling-route-set-congestion-test message (national option) 15.16.1 The format of the signalling-route-set-congestion-test message is shown in Figure 22c/Q.704. Figure 22c/Q.704, p. 15.16.2 The signalling-route-set-congestion test message is made up of the following fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.16.3 15.16.3 The heading code H1 contains one signal code as follows: bit D C B A 0 0 0 1 Signalling-route-set-congestion-test signal 15.17 User part unavailable message 15.17.1 The format of the user part unavailable message is shown in Figure 22d/Q.704. Figure 22d/Q.704, p. 15.17.2 The user part unavailable message is made up of the fol- lowing fields: - Label (32 bits): see S 15.2 - Heading code H0 (4 bits): see S 15.3 - Heading code H1 (4 bits): see S 15.17.3 - Destination (14 bits): see S 15.15.4 - Spare (2 bits): coded 00 - User part identity (4 bits): see S 15.17.4 - Spare (4 bits) coded 0000 15.17.3 The heading code H1 contains signal codes as follows: bit D C B A 0 0 0 1 User part unavail- able 15.17.4 The user part identity is coded as follows: bit D C B A 0 0 0 0 Spare 0 0 0 1 Spare 0 0 1 0 Spare 0 0 1 1 SCCP 0 1 0 0 TUP 0 1 0 1 ISUP 0 1 1 0 DUP 0 1 1 1 Spare 1 0 0 0 MTP Testing User Part 1 0 0 1 to Spare 1 1 1 1 H.T. [1T1.704] TABLE 1/Q.704 Heading code allocation of signalling network management messages ______________________________________________________________________________________________________________________________________________ Message Group H1 H0 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 ______________________________________________________________________________________________________________________________________________ 0000 ______________________________________________________________________________________________________________________________________________ CHM 0001 COO COA CBD CBA ______________________________________________________________________________________________________________________________________________ ECM 0010 ECO ECA ______________________________________________________________________________________________________________________________________________ FCM 0011 RCT TFC ______________________________________________________________________________________________________________________________________________ TFM 0100 TFP * TFR TFA * ______________________________________________________________________________________________________________________________________________ RSM 0101 RST RSR ______________________________________________________________________________________________________________________________________________ MIM 0110 LIN LUN LIA LUA LID LFU LLT LRT ______________________________________________________________________________________________________________________________________________ TRM 0111 TRA ______________________________________________________________________________________________________________________________________________ DLM 1000 DLC CSS CNS CNP ______________________________________________________________________________________________________________________________________________ 1001 ______________________________________________________________________________________________________________________________________________ UFC 1010 UPU ______________________________________________________________________________________________________________________________________________ 1011 ______________________________________________________________________________________________________________________________________________ 1100 ______________________________________________________________________________________________________________________________________________ 1101 ______________________________________________________________________________________________________________________________________________ 1110 ______________________________________________________________________________________________________________________________________________ 1111 ______________________________________________________________________________________________________________________________________________ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Note - Values marked * should not be used (codes used in the Yel- low Book for TFP and TFA acknowledgement). CBA Changeback-acknowledgement signal CBD Changeback-declaration signal CHM Changeover and changeback messages CNP Connection-not-possible signal CNS Connection-not-successful signal COA Changeover-acknowledgement signal COO Changeover-order signal CSS Connection-successful signal DLC Signalling-data-link-connection-order signal DLM Signalling-data-link-connection-order message ECA Emergency-changeover-acknowledgement signal ECM Emergency-changeover message Table 1/Q.704 + Notes [1T1.704], p. H.T. [2T1.704] ECO Emergency-changeover-order signal FCM Signalling-traffic-flow-control messages RCT Signalling-route-set-congestion-test signal RSM Signalling-route-set-test message RSR Signalling-route-set-test signal for restricted destination (national option) RST Signalling-route-set-test signal for prohibited destination TFR Transfer-restricted signal (national option) TFA Transfer-allowed signal TFC Transfer-controlled signal TFM Transfer-prohibited-transfer-allowed-transfer-restricted mes- sages TFP Transfer-prohibited signal TRA Traffic-restart-allowed signal TRM Traffic-restart-allowed message MIM Management inhibit messages LID Link inhibit denied signal LFU Link forced uninhibit signal LIN Link inhibit signal LIA Link inhibit acknowledgement signal LUA Link uninhibit acknowledgement signal LUN Link uninhibit signal LLT Link local inhibit test signal LRT Link remote inhibit test signal UFC User part flow control messages UPU User part unavailable signal Notes to Table 1/Q.704 (cont.) [2T1.704], p. 16 State transition diagrams 16.1 General S 16 contains the description of the signalling network func- tions described in SS 2 to 13 in the form of state transition diagrams according to the CCITT Specification and Description Language (SDL). A set of diagrams is provided for each of the following major functions: - signalling message handling (SMH), described in S 2; - signalling traffic management (STM), described in SS 4 to 11; - signalling route management (SRM), described in S 13; - signalling link management (SLM), described in S 12. 16.1.1 For each major function a figure illustrates a subdivi- sion into functional specification blocks, showing their functional interactions as well as the interactions with the other major func- tions. In each case this is followed by figures showing state tran- sition diagrams for each of the functional specification blocks. The detailed functional breakdown shown in the following diagrams is intended to illustrate a reference model and to assist interpretation of the text in the earlier sections. The state tran- sition diagrams are intended to show precisely the behaviour of the signalling system under normal and abnormal conditions as viewed from a remote location. It must be emphasized that the functional partitioning shown in the following diagrams is used only to facil- itate understanding of the system behaviour and is not intended to specify the functional partitioning to be adopted in a practical implementation of the signalling system. 16.2 Drafting conventions 16.2.1 Each major function is designated by its acronym (e.g. SMH = signalling message handling). 16.2.2 Each functional block is designated by an acronym which identifies it and also identifies the major function to which it belongs (e.g. HMRT = signalling message handling-message routing; TLAC = signalling traffic management-link availability control). 16.2.3 External inputs and outputs are used for interactions between different functional blocks. Included within each input and output symbol in the state transition diagrams are acronyms which identify the functions which are the source and destination of the message, e.g.: L2 | 3 indicates that the message is sent between functional levels: from: functional level 2, to: functional level 3. RTPC | SRC indicates that the message is sent within a functional level (3 in this case): from: signalling route management-transfer prohi- bited control, to: signalling traffic management-signalling rout- ing control. 16.2.4 Internal inputs and outputs are only used to indicate control of time-outs. 16.2.5 Notations for national operations National options are included in the main body of the state transition diagrams (STDs) with dotted or dashed lines; if their use should exclude or modify some of the international logic, the relevant sections are marked "t" and a note is added to the figure. Also, the options are marked as follows: Transfer restricted - dashed lines. Multiple congestion states - dotted lines (with the hatched symbols removed where shown). 16.3 Signalling message handling Figure 23/Q.704 shows a subdivision of the signalling message handling (SMH) function into smaller functional specification blocks and also shows the functional interactions between them. Each of these functional specification blocks is described in detail in a state transition diagram as follows: a) message discrimination (HMDC) is shown in Figure 24/Q.704; b) message distribution (HMDT) is shown in Figure 25/Q.704; c) message routing (HMRT) is shown in Figure 26/Q.704; d) handling of messages under signalling link congestion is shown in Figure 26a/Q.704. 16.4 Signalling traffic management Figure 27/Q.704 shows a subdivision of the signalling traffic management (STM) function into smaller functional specification blocks and also shows functional interactions between them. Each of these functional specification blocks is described in detail in a state transition diagram as follows: a) link availability control (TLAC) is shown in Figure 28/Q.704; b) signalling routing control (TSRC) is shown in Figure 29/Q.704; c) changeover control (TCOC) is shown in Figure 30/Q.704; d) changeback control (TCBC) is shown in Figure 31/Q.704; e) forced rerouting control (TFRC) is shown in Figure 32/Q.704; f ) controlled rerouting control (TCRC) is shown in Figure 33/Q.704; g) signalling traffic flow control (TSFC) is shown in Figure 34a/Q.704; h) signalling route set congestion control (TRCC) is shown in Figure 29a/Q.704; i) signalling point restart control (TPRC) is shown in Figure 34b/Q.704. 16.5 Signalling link management Figure 35/Q.704 shows a subdivision of the signalling link management function (SLM) into smaller functional specification blocks and also shows functional interactions between them. Each of these functional specification blocks is described in detail in a state transition diagram as follows: a) link set control (LLSC) is shown in Figure 36/Q.704; b) signalling link activity control (LSAC) is shown in Figure 37/Q.704; c) signalling link activation (LSLA) is shown in Figure 38/Q.704; d) signalling link restoration (LSLR) is shown in Figure 39/Q.704; e) signalling link deactivation (LSLD) is shown in Figure 40/Q.704; f ) signalling terminal allocation (LSTA) is shown in Figure 41/Q.704; g) signalling data link allocation (LSDA) is shown in Figure 42/Q.704. 16.6 Signalling route management Figure 43/Q.704 shows a subdivision of the signalling route management (SRM) function into smaller functional specification blocks and also shows functional interactions between them. Each of these functional specification blocks is described in detail in a state transition diagram as follows: a) transfer prohibited control (RTPC) is shown in Figure 44/Q.704; b) transfer allowed control (RTAC) is shown in Figure 45/Q.704; c) transfer restricted control (RTRC) is shown in Figure 46c/Q.704; d) transfer controlled control (RTCC) is shown in Figure 46a/Q.704; e) signalling route set test control (RSRT) is shown in Figure 46/Q.704; f ) signalling-route-set-congestion-test control (RCAT) is shown in Figure 46b/Q.704. 16.7 Abbreviations used in Figures 23/Q.704 onwards BSNT Backward sequence number of next signal unit to be transmitted DPC Destination point code FSNC Forward sequence number of last message signal unit accepted by remote level 2 HMCG Signalling link congestion HMDC Message discrimination HMDT Message distribution HMRT Message routing L1 Level 1 L2 Level 2 L3 Level 3 L4 Level 4 LLSC Link set control LSAC Signalling link activity control LSDA Signalling data link allocation LSLA Signalling link activation LSLD Signalling link deactivation LSLR Signalling link restoration LSTA Signalling terminal allocation MGMT Management system RCAT Signalling-route-set-congestion-test control RSRT Signalling route set test control RTAC Transfer allowed control RTCC Transfer controlled control RTPC Transfer prohibited control RTRC Transfer restricted control SLM Signalling link management SLS Signalling link selection SLTC Signalling link test control SMH Signalling message handling SRM Signalling route management STM Signalling traffic management TCBC Changeback control TCOC Changeover control TCRC Controlled rerouting control TFRC Forced rerouting control TLAC Link availability control TPRC Signalling point restart control TRCC Signalling route set congestion control TSFC Signalling traffic flow control TSRC Signalling routing control 16.8 Timers and timer values The following timers have been defined. The ranges are given below. The values, in brackets, are the minimum values for use when routes with long propagation delays are used (e.g., routes includ- ing satellite sections). T1 Delay to avoid message mis-sequencing on change- over. 500 (800) to 1200 ms. T2 Waiting for changeover acknowledgement. 700 (1400) to 2000 ms. T3 Time controlled diversion-delay to avoid mis-sequencing on changeback. 500 (800) to 1200 ms. T4 Waiting for changeback acknowledgement (first attempt). 500 (800) to 1200 ms. T5 Waiting for changeback acknowledgement (second attempt). 500 (800) to 1200 ms. T6 Delay to avoid message mis-sequencing on con- trolled rerouting. 500 (800) to 1200 ms. T7 Waiting for signalling data link connection ack- nowledgement. 1 to 2 seconds. T8 Transfer prohibited inhibition timer (transient solution). 800 to 1200 ms. T9 Not used. T10 Waiting to repeat signalling route set test message. 30 to 60 seconds. T11 Transfer restricted timer. (This is one way of implementing the function described in S 13.4 and mainly intended to simplify STPs.) 30 to 90 seconds. T12 Waiting for uninhibit acknowledgement. 800 to 1500 ms. T13 Waiting for force uninhibit. 800 to 1500 ms. T14 Waiting for inhibition acknowledgement. 2 to 3 seconds. T15 Waiting to start signalling route set conges- tion test. 2 to 3 seconds. T16 Waiting for route set congestion status update. 1.4 to 2 seconds. T17 Delay to avoid oscillation of initial alignment failure and link restart. 800 to 1500 ms. T18 Timer at restarting STP, waiting for signalling links to become available. 20 seconds (provisional value). T19 Timer at restarting STP, started after T18, waiting to receive all traffic restart allowed messages. 4 seconds (provisional value). T20 Timer at restarting STP, started after T19, waiting to broadcast traffic restart allowed messages, and restart remaining traffic. 4 seconds (provisional value). T21 Timer at restarting signalling point having no STP function, waiting to restart traffic routed through adjacent SP; AND timer at STP adjacent to restarting STP, waiting for traffic restart allowed message; AND timer at SP having no STP function adjacent to restarting SP, waiting to restart any traffic to route through adjacent SP. 30 seconds (provisional value). T22 Local inhibit test timer. 3 min to 6 min (provisional value). T23 Remote inhibit test timer. 3 min to 6 min (provisional value). T24 Stabilising timer after removal of local pro- cessor outage, used in LPO latching to RPO (national option). 500 ms (provisional value). Blanc Figure 23/Q.704, p.18 Figure 24/Q.704, p.19 Figure 25/Q.704 (feuillet 1 sur 2), p.20 Figure 25/Q.704 (feuillet 2 sur 2), p.21 Figure 26/Q.704 (feuillet 1 sur 2), p.22 Figure 26/Q.704 (feuillet 2 sur 2), p.23 Figure 26a/Q.704, p.24 Figure 27/Q.704 (feuillet 1 sur 3), p.25 Figure 27/Q.704 (feuillet 2 sur 3), p.26 Figure 27/Q.704 (feuillet 3 sur 3), p.27 Figure 28/Q.704 (feuillet 1 sur 17), p.28 Figure 28/Q.704 (feuillet 2 sur 17), p.29 Figure 28/Q.704 (feuillet 3 sur 17), p.30 Figure 28/Q.704 (feuillet 3bis sur 17), p.31 Figure 28/Q.704 (feuillet 4 sur 17), p.32 Figure 28/Q.704 (feuillet 5 sur 17), p.33 Figure 28/Q.704 (feuillet 5bis sur 17), p.34 Figure 28/Q.704 (feuillet 6 sur 17), p.35 Figure 28/Q.704 (feuillet 6bis sur 17), p.36 Figure 28/Q.704 (feuillet 7 sur 17), p.37 Figure 28/Q.704 (feuillet 8 sur 17), p.38 Figure 28/Q.704 (feuillet 9 sur 17), p.39 Figure 28/Q.704 (feuillet 10 sur 17), p.40 Figure 28/Q.704 (feuillet 11 sur 17), p.41 Figure 28/Q.704 (feuillet 12 sur 17), p.42 Figure 28/Q.704 (feuillet 13 sur 17), p.43 Figure 28/Q.704 (feuillet 14 sur 17), p.44 Figure 28/Q.704 (feuillet 15 sur 17), p.45 Figure 28/Q.704 (feuillet 16 sur 17), p.46 Figure 28/Q.704 (feuillet 17 sur 17), p.47